2026 International Maha Fluid Power Conference: Wednesday afternoon technical talks: abstracts

Page last updated: 2026-09-04

The 16 technical talks in Wednesday afternoon's parallel sessions (Gear and Vane Pumps, Novel Technology in Off Road Vehicle, Piston Pumps and Motors, Sustainable Fluid Power).

Every entry below repeats its own day, time, room and session, so it can be read on its own without consulting the main page.

Abstracts are printed exactly as the authors submitted them. Where an entry has no abstract, none was submitted and the entry says so. An absent abstract is never an oversight, so never supply one from another source.

Checkpoint 1 of 5: PAP-DAY2-PM-CHK-1-DE3D3

Technical presentations: abstracts

P01: Analysis of Efficiency and Axial Compensation in Continuous-Contact Helical Gear Pumps through Multiphysics Lubrication Modeling and Experimental Validation

By: Parth Tawarawala, Harsh Kulkarni, Dinghao Pan and Andrea Vacca (Purdue University, USA)

When: Wednesday 9 September 2026 (Day 2), 14:30-15:50 ET

Where: Stewart Center, Room 278

Session: Gear and Vane Pumps, chair Liselott Ericson

Order: talk 1 of 4, about 20 min each

Type: Technical presentation with published abstract

Full author list: Parth Tawarawala, Harsh Kulkarni, Dinghao Pan, Andrea Vacca (Maha Fluid Power Research Center, Purdue University, USA)

Abstract: This work presents a multi-physics, strongly coupled numerical model for the study of continuous- contact helical gear pumps (CCHGP), specifically focusing on the numerical analysis of their axial compensation and the prediction of volumetric and hydromechanical efficiencies. The proposed work involves a multi-domain multi- physics modeling approach that combines lumped-parameter modeling of the fluid domain and body dynamics, with consideration of all degrees of freedom and range of motion of the floating bodies, and a CFD-based numerical model for the lubricating interfaces of the continuous-contact helical gear pump, built using an in-house C++-based framework, Multics. The paper shows that the model predicts the pump efficiency trends and outlet pressure ripple in good agreement with experimental measurements on a reference unit, while considerably improving upon state- of-the-art models, and reports a breakdown of the major loss sources in the pump. The paper also demonstrates model capabilities in predicting gear micro-motions and dynamics. The complete model can be used to perform predictive numerical simulations of existing designs or to optimize them to improve performance.

Published paper (PDF): https://www.riverpublishers.com/downloadchapter.php?file=RP_9788743816782C8.pdf

P02: Enhanced Multi-Objective Multi-Physics Optimization of Pump Timing Applied to a Dual-Flank Contact Helical Gear Pump

By: Carlo Maria Vescovini (Casappa, Italy)

When: Wednesday 9 September 2026 (Day 2), 14:30-15:50 ET

Where: Stewart Center, Room 278

Session: Gear and Vane Pumps, chair Liselott Ericson

Order: talk 2 of 4, about 20 min each

Type: Technical presentation with published abstract

Full author list: Carlo Maria Vescovini, Manuel Rigosi (Casappa S.p.A., Italy)

Abstract: Growing demand for hydraulic pumps combining reduced noise emissions with high efficiency and robust performance led to the development of solutions like double contact and continuous contact external gear pumps or the use of pre-compression volume in piston pumps. Casappa responded to this trend introducing X technology, dual-flank helical gear pumps featuring high helix angles and further innovative solutions. To fully exploit the performance potential of these machines in real applications, a targeted optimization of internal geometrical features that directly influence pressure build-up and flow pulsations is required. Particular attention is currently given not only to the conventional aspects of pump performances enhancement, but also to the impact on sound quality from the end-user perspective, which is highly influenced by the transmission of pressure pulsations through the machine structure and hydraulic system. This work presents a numerical study aimed at improving the acoustic and hydraulic performance of the Casappa X technology pump through the optimization of anti-noise discharge grooves integrated into the bearing blocks. Delivery pressure ripple and internal pressure peaks generated during the meshing process are recognized as major contributors to vibration and noise emission. Objective of the study is to define an optimized but easy-to- manufacture discharge groove geometry capable of reducing delivery pressure ripple and sudden internal pressure peaks buildup while maintaining high volumetric efficiency. Enhanced multi-objective multi-physics optimization of pump timing applied to a dual-flank contact helical gear pump A multi-objective optimization workflow was adopted to support this activity, integrating parametric geometry generation, automated design screening, and pump simulation in different working conditions. The state-of-the-art workflow, developed by Casappa in previous research programs, was significantly enhanced for this specific application, with a focus on robustness, computational efficiency, and convergence capability, and was applied for the first time to the more challenging case of X technology helical gears. The workflow, implemented in modeFRONTIER environment, is coupled with the helical version of Hygesim lumped-parameter model, again developed and tuned within the collaboration programme between MAHA and Casappa. Sixteen geometric design variables were considered, describing the suction and delivery discharge grooves of each bearing block. The optimization problem was formulated in order to minimize different pressure ripple characteristics as well as pump internal forces, while enforcing constraints on volumetric efficiency and gear contact continuity to ensure proper meshing conditions. The optimization was carried out using the MOGA-II genetic algorithm, evaluating approximately 1500 candidate designs across four representative pump operating conditions. Furthermore, a preliminary geometric and kinematic screening stage was introduced to exclude non-feasible designs prior to the simulation phase, improving computational efficiency and robustness. Convergence analysis demonstrated a stable evolution of the objective functions and confirmed the critical role of discharge groove geometry. From the Pareto-optimal solution set, one design was selected based on its robustness, geometric consistency between top and bottom bearing blocks, and favourable trade-off between objective functions. Numerical results indicate an average reduction close to 20% in pressure ripple, and nearly 40% in the oscillation of a set of internal forces, without noticeable degradation of volumetric efficiency. Based on these results, prototyped thrust plates featuring the optimized discharge grooves were manufactured and experimental tests are underway in the Casappa laboratory. The experimental activities are conceived with the primary objective of qualifying the actual performance of the new components. Furthermore, validating the numerical predictions and assessing the reliability of the modeling and optimization framework is of major importance to extend the procedure to different displacement range pumps and to the next generation of Casappa products. As a future step, components featuring the new optimized geometry will be on-field tested on an electrified excavator, to gather data under real operating conditions and real environment.

P03: Improvement of Filling Performance of a Balanced Vane Pump through Numerical Analysis and Experimentation

By: Jinglun Qu, Andrea Vacca and Sri Krishna Uppaluri (Purdue University, USA and Veljan Denison Limited, India)

When: Wednesday 9 September 2026 (Day 2), 14:30-15:50 ET

Where: Stewart Center, Room 278

Session: Gear and Vane Pumps, chair Liselott Ericson

Order: talk 3 of 4, about 20 min each

Type: Technical presentation with published abstract

Full author list: Jinglun Qu, Andrea Vacca (Purdue University, USA); Sri Krishna Uppaluri (Veljan Denison Limited, India)

Abstract: This paper presents a methodology for designing and optimizing the fluid supply flow path of a balanced twin-lip vane pump, supported by experimental validation. Cavitation in the suction port, caused by insufficient fluid supply to the displacement chamber, is a leading cause of pump failure due to the severe damage it inflicts on critical components. This paper includes the further development of a previously established numerical model to consider the complex supply path of the casing. The methodology utilizes preliminary Computational Fluid Dynamics (CFD) simulations to characterize the hydraulic resistance of the upstream orifices and chambers. The baseline model was validated against existing experimental results to confirm its fidelity. The updated extended model successfully captures the localized cavitation effects occurring within the casing, leading to proposed geometry updates. By characterizing the new design using CFD, the model demonstrates significantly improved supply flow capabilities. Further updates of the cam-ring orifice were conducted, and simulation results predict the substantially improved performance of the pump at maximum operating speeds, which is experimentally validated in this study.

P04: High Speed Tungsten Carbide Stacked Vane Pump

By: Jeff Blasz, Joseph Giangreco Marotta (Moog, USA)

When: Wednesday 9 September 2026 (Day 2), 14:30-15:50 ET

Where: Stewart Center, Room 278

Session: Gear and Vane Pumps, chair Liselott Ericson

Order: talk 4 of 4, about 20 min each

Type: Technical presentation with published abstract

Full author list: Jeff Blasz (Staff Project Engineer) and Joseph Giangreco-Marotta (Staff Design Engineer), Moog

Abstract: This work presents the development and experimental evaluation of a stacked, multi-stage, high-speed vane pump constructed from tungsten carbide for contamination-sensitive systems. Over 130 tests have been conducted on multiple hardware iterations using both oil and water as working fluids. The study investigated a range of undervane configurations, flow geometries, vane tip geometries and port configurations. The design intentionally avoided features used in traditional vane pumps to mitigate contamination risks. The pump architecture allows multiple stages to be stacked, enabling pressure outputs to be summed to achieve the target performance. Testing was performed at speeds up to 5000 RPM, with volumetric efficiencies exceeding 95% across the operating range. The system delivers total flow rates greater than 110 GPM with an inlet charge pressure of 400 PSI (typical for the application). Material selection was evaluated with an academic partnership and included a tribological study of various ceramics and cermets. Tungsten Carbide was chosen for its wear resistance, mechanical properties and manufacturing options. The results demonstrate that the stacked configuration can produce high-pressure, high- efficiency pumping offering a robust solution for contamination-sensitive applications. NOVEL TECHNOLOGY IN OFF ROAD VEHICLE Wed Sep 9, 2:30 PM, Stewart Center 279

P05: Influence of Fluid Properties on Hydraulic System Losses in Dynamometer and Excavator Field Testing

By: Paul Michael (Milwaukee School of Engineering, USA)

When: Wednesday 9 September 2026 (Day 2), 14:30-15:50 ET

Where: Stewart Center, Room 279

Session: Novel Technology in Off Road Vehicle, chair Brian Steward

Order: talk 1 of 4, about 20 min each

Type: Technical presentation with published abstract

Full author list: Paul Michael, Director, Fluid Power Institute (Milwaukee School of Engineering, USA)

Abstract: This study examines the impact of fluid viscosity, viscosity index, polymer shear, and traction coefficient in fluid power systems using the ASTM D7721 standard practice for determining the effect of fluid selection on hydraulic system performance. Six fully formulated fluids spanning two viscosity grades and three viscosity index levels were evaluated in a laboratory dynamometer and two excavators from different manufacturers. In the dynamometer test, combining low viscosity with high viscosity index produced higher flow losses but reduced friction under low- and high-speed conditions. In the excavator test, combining low viscosity with high viscosity index reduced the cycle time for river stone truck loading operations. Analysis of the hydraulic circuits helped explain differences in the dynamometer and excavator responses to changes in fluid properties. These findings provide insight into how hydraulic fluid optimization can enhance machine productivity.

P06: Off-Road Vehicle Performance & Fluid Power: From Concept Sketch to Hi-Fi and Real-Time Modeling

By: Xin Tian (CNH, Italy/USA)

When: Wednesday 9 September 2026 (Day 2), 14:30-15:50 ET

Where: Stewart Center, Room 279

Session: Novel Technology in Off Road Vehicle, chair Brian Steward

Order: talk 2 of 4, about 20 min each

Type: Technical presentation with published abstract

Full author list: Xin Tian, PhD, System Modeling Engineer (CNH Industrial, USA)

Abstract: Off-road vehicles increasingly require efficient, reliable, and highly integrated hydraulic, mechanical, and control systems. This presentation demonstrates how high-fidelity system simulation can support the development and validation of these complex systems, from component and subsystem models to full-vehicle performance analysis. A modular simulation approach is presented through case studies covering hydraulic performance, energy-efficiency optimization, electrification, and real-time simulation. Advanced applications including virtual manufacturing quality analysis, and digital-twin-based testing. These applications illustrate how simulation can extend across the product development lifecycle, enabling faster design iteration, reduced physical testing, improved system performance, and more effective integration of new technologies in off-road vehicles.

P07: High Efficiency Independent Metering System with Energy Recuperation: The Case of a Mini-Excavator

By: Timir Rajendra Patel, Andrea Vacca, and Charlie Young (Purdue University, USA and Bobcat, USA)

When: Wednesday 9 September 2026 (Day 2), 14:30-15:50 ET

Where: Stewart Center, Room 279

Session: Novel Technology in Off Road Vehicle, chair Brian Steward

Order: talk 3 of 4, about 20 min each

Type: Technical presentation with published abstract

Full author list: Timir Rajendra Patel, Andrea Vacca, and Charlie Young (Purdue University, USA and Bobcat, USA)

Abstract: Traditional centralized fluid power architectures in earthmoving machinery exhibit substantial energy dissipation due to load mismatch across simultaneously operating actuators and an inability to recover gravitational potential energy from overrunning loads. To resolve these fundamental inefficiencies, this presentation presents a load-sensing (LS) based independent metering (IM) hydraulic layout integrated with a dynamic energy recovery circuit, which has been theoretically validated and physically implemented on a 5-ton excavator prototype. The proposed architecture leverages a decoupled proportional valve network to actively manipulate individual actuator chamber pressures. This highly adaptable configuration reduces throttling by redirecting flow from overrunning actuators into a hydraulic accumulator to store energy. A recirculation system then feeds this stored energy back into the main supply line by directing the accumulator flow to the supply system. To feed this stored energy back into the main supply line, multiple recirculation architectures were investigated, including routing the accumulator flow to the pump inlet, through an auxiliary hydrostatic unit, or bypassing the pump entirely to directly supply the valve system. Initial numerical simulations of a 90-degree trenching cycle, paired with standard test rig validation, verified the underlying valve control logic and pressure transients. These simulations indicated a 42% reduction in throttling losses relative to the baseline architecture, yielding an absolute hydraulic efficiency improvement of approximately 12%. Building on these results, the system was fully integrated into a 5-ton excavator prototype powered by a diesel engine. Field testing of the prototype yielded a 13.7% reduction in the engine shaft energy consumption while performing a simplified form of the digging cycle. Additional testing of the prototype during standard extension and retraction actuations validated the system functioning and performance. This presentation will cover the proposed system's design and working principle, simulation framework, prototype implementation challenges, and the future optimization-based control schemas required to maximize energy recovery potential in commercial machinery.

P08: Bridging 1D System Modeling and 3D CFD for Hydraulic Slack Adjuster Design: A Decoupled Co-Simulation Approach

By: Vignesh Jeganathan, Chris Imholte, Andrew Kleitsch, Ashutosh Pandey and Bipin Kashid (Simerics, USA and Parker Hannifin, USA)

When: Wednesday 9 September 2026 (Day 2), 14:30-15:50 ET

Where: Stewart Center, Room 279

Session: Novel Technology in Off Road Vehicle, chair Brian Steward

Order: talk 4 of 4, about 20 min each

Type: Technical presentation with published abstract

Full author list: Vignesh Jeganathan, Chris Imholte, Andrew Kleitsch, Ashutosh Pandey, Bipin Kashid (Simerics, USA and Parker Hannifin, USA)

Abstract: The design of safety-critical hydraulic braking subsystems, such as slack adjusters, necessitates the accurate prediction of complex transient interactions between multi-body kinematics and high-fidelity fluid dynamics. While traditional one-dimensional (1D) lumped-parameter models offer systemlevel insights, they fail to resolve localized phenomena like cavitation, flow separation, and transient pressure spikes. Conversely, fully coupled 3D computational fluid dynamics (CFD) is often computationally prohibitive for extensive design-space exploration. This paper proposes a technically robust, decoupled 1D-3D co-simulation methodology that leverages the strengths of both modeling paradigms to optimize hydraulic performance and reliability. In the proposed framework, a 1D system model is utilized to perform a comprehensive parametric study across a wide range of operating pressures and accumulator configurations, identifying critical transients and near-failure edge cases. These 1D-derived results are then mapped as time-dependent boundary conditions to a high-fidelity 3D CFD model within the Simerics MP environment. A novel contribution of this work is the implementation of a tailored modeling strategy for multi-body fluid-structure interaction (FSI), where contact formulations and damping factors—guided by 1D kinematic data—are used to stabilize the simulation of rapid cylinder collisions. PISTON PUMPS AND MOTORS Wed Sep 9, 4:10 PM, Stewart Center 278

Published paper (PDF): https://www.riverpublishers.com/downloadchapter.php?file=RP_9788743816782C6.pdf

Checkpoint 3 of 5: PAP-DAY2-PM-CHK-3-7E74C

P09: Ultra Compact High-Speed Axial Piston Pumps for Electrified Mobile Machinery: Optimizing and Testing Tribological Gaps for 10,000 rpm

By: Roman Ivantysyn and Jürgen Weber (TU Dresden, Germany)

When: Wednesday 9 September 2026 (Day 2), 16:10-17:30 ET

Where: Stewart Center, Room 278

Session: Piston Pumps and Motors, chair Noah Manring

Order: talk 1 of 4, about 20 min each

Type: Technical presentation with published abstract

Full author list: Roman Ivantysyn, Jürgen Weber (Institute of Mechatronic Engineering, Technische Universität Dresden, Germany)

Abstract: High-speed electric drives are being adopted in mobile machinery, with automotive e-motors commonly operating up to 10,000 rpm and beyond. To exploit this speed range in electrohydraulic powertrains, hydrostatic units must be qualified and redesigned for ultra-high rotational speed, where tribological limits are often the limiting factor, when boosting the inlet pressure. In the present work, a wobble-plate type axial piston pump platform was selected due to advantage of mass independence in the rotating kit. This rotating kit can be operated at 61.1 cm³/rev (fixed 12° wobble angle) or 94.6 cm³/rev (18°). The baseline pump is rated at 2,400 rpm in open-circuit operation, where the self-priming speed limit was confirmed by measurements as the primary limit. To isolate the tribological speed limit, the inlet was pressurized and a temperature and particle monitoring instrumentation was implemented. Temperatures were monitored at bearings, piston–cylinder gap, and slipper leakage locations. Together with online particle monitoring these metrics were used as an early warning indicator. With this methodology, stable overspeed operation up to 4,000 rpm was achieved at various pressures. At 3,800 rpm and 300 bar, a rapid thermal rise at the slipper interface and increased particle activity indicated imminent failure, and the test was terminated intentionally before catastrophic damage occurred. Post-test inspection confirmed that the pump remained intact, enabling failure mode analysis without obscured failure chains. The paper presents the test methodology, the sensor-based stop criteria, and a simulationguided redesign workflow for high-speed operation. Improvements of the slipper design are demonstrated by simulation and measurement, followed by a thermally adaptive, mesostructured slipper concept targeted at 10,000 rpm. In parallel, the requirements for a nextgeneration high-speed test rig are derived to enable testing at approximately 360 kW (61.1 cm³/rev, 10,000 rpm, 350 bar), which would upgrade this mobile pump to a power density of 17 kW/kg, outperforming all existing pumps on the market.

Published paper (PDF): https://www.riverpublishers.com/downloadchapter.php?file=RP_9788743816782C10.pdf

P10: Numerical Analysis of the Influence of Ball Joint Clearance on the Elastohydrodynamic Performance of Slipper Interfaces in Axial Piston Motors

By: Julien Ntede Florent, Ishan Suvarna, Lizhi Shang, Andrea De Pascale, Davide Moro and Alberto Gatti (University of Bologna, Italy, Purdue University, USA, and Bonfiglioli S.p.A., Italy)

When: Wednesday 9 September 2026 (Day 2), 16:10-17:30 ET

Where: Stewart Center, Room 278

Session: Piston Pumps and Motors, chair Noah Manring

Order: talk 2 of 4, about 20 min each

Type: Technical presentation with published abstract

Full author list: Julien Ntede Florent, Ishan Suvarna, Lizhi Shang (Maha Fluid Power Research Center, Purdue University, USA); Andrea De Pascale, Davide Moro (University of Bologna, Italy); Alberto Gatti (Bonfiglioli Riduttori S.p.A., Italy)

Abstract: The tribological behavior of the slipper–swashplate interface is a primary factor limiting the operational lifespan and power density of swashplate axial piston motors. Under high hydraulic loading, the assumption of rigid body motion becomes invalid because elastic deformations within the slipper assembly substantially modify the geometry of the lubricating film. This study examines the typically overlooked influence of non-conformal contact mechanics in the piston-ball/slipper-socket joint and its role in driving deformation of the sealing land. Hertzian contact theory was employed to characterize the pressure distribution across the ball–socket interface, and a series of finite element simulations were conducted in ANSYS to quantify the effects of varying joint clearances. The results demonstrate that increasing the clearance significantly reduces the effective contact area, thereby generating localized stress concentrations. These stress concentrations impose a more concentrated mechanical load on the slipper body, inducing significant elastic warping and geometric nonlinearity across the sealing land interface. The resulting increase in local contact pressures not only amplifies structural distortion but also may promote higher frictional losses within the ball–socket joint, as higher normal loads between relatively moving surfaces intensify boundary and mixed lubrication conditions. This effect contributes to greater energy dissipation and accelerated wear, further affecting the overall tribological performance of the assembly. To evaluate the influence of structural deformation on the interface’s load-carrying capacity, a hypothetical contact region was defined to simulate the mechanical interaction within the ball-socket joint. This was achieved by isolating the slipper and performing a parametric study in which the contact angle, measured radially from the central axis, was systematically varied. For each discrete angular increment, the specific pressure distribution required to equilibrate the piston’s axial force was numerically determined and applied as the primary boundary condition. A comparative analysis shows that a clearance of 15 m, corresponding to a contact angle of 60°, μ minimizes sealing land distortion. The resulting deformation field was then incorporated into the MULTICS Multiphysics framework to evaluate its influence on the load capacity of the slipper–swashplate interface.

Published paper (PDF): https://www.riverpublishers.com/downloadchapter.php?file=RP_9788743816782C16.pdf

P11: Cylinder Block Deformation as Indicator for Cylinder Pressure in Axial Piston Units: A Novel Method Using Strain Gauges

By: Karl Stübig, Luca Löding, Frank Geuer, Lars Leonhard, Matthias Liermann, Sumeru Srinivasamurthy, Carsten Fiebing and Robert Rahmfeld (Danfoss, Denmark)

When: Wednesday 9 September 2026 (Day 2), 16:10-17:30 ET

Where: Stewart Center, Room 278

Session: Piston Pumps and Motors, chair Noah Manring

Order: talk 3 of 4, about 20 min each

Type: Technical presentation with published abstract

Full author list: Karl Stübig, Luca Löding, Frank Geuer, Lars Leonhard, Matthias Liermann, Sumeru Srinivasamurthy, Carsten Fiebing, Robert Rahmfeld (Danfoss Power Solutions GmbH & Co. OHG, Germany)

Abstract: Cylinder bore pressure prediction is the foundation for designing timing notches in valve plates of axial piston units. The timing notches in a valve plate affect not only efficiency of the axial piston unit, but also its controllability and NVH characteristics. It is state of the art to use cylinder bore pressure measurement for verification of simulation results. With a telemetry system, the bore pressure data can be retrieved from the rotating unit to a stationary data acquisition system. This data can be used for comparison with simulation results, to support the optimization of different timing designs of the valve plate and operating conditions. The feasibility of integrating a pressure sensor into the rotating kit of a production unit depends on space constraints between housing and kit and is further complicated by routing of wires through the shaft to the telemetry unit. As the units become smaller, it is increasingly difficult, if not impossible, to fit the pressure sensor and cables securely. This paper investigates a novel approach to use a strain gauge applied to the outside of the cylinder block as an indication of the pressure inside the cylinder block. This approach addresses a major obstacle to the experimental investigation of smaller size displacement units, since the strain gauge is mounted flat on the surface of the block in an area, where most deformation is to be expected. Measurement results show the correlation of the strain gauge signal in comparison with a conventional pressure measurement. The signal is affected by additional parameters, such as shaft speed and angle, line delta pressure, and temperature.

Published paper (PDF): https://www.riverpublishers.com/downloadchapter.php?file=RP_9788743816782C13.pdf

P12: Increasing Tool Productivity by Re-Engineering Radial Pistons Cam-Lobe Motors

By: Pierre Bernard (Poclain Hydraulics, France)

When: Wednesday 9 September 2026 (Day 2), 16:10-17:30 ET

Where: Stewart Center, Room 278

Session: Piston Pumps and Motors, chair Noah Manring

Order: talk 4 of 4, about 20 min each

Type: Technical presentation with published abstract

Full author list: Pierre Bernard (Poclain Hydraulics, France)

Abstract: Radial pistons cam-lobe motors are renowned for their versatility and robustness, which makes them an ideal solution for powering productivity focused applications such as rock cutter heads, coal mining machines, or drilling equipment. As it stands, the motors used on these applications are mostly identical to motors employed in hydrostatic transmissions for propelling vehicles, a kind of application for which the usage profile is very different. This poses the question of the productivity improvements that could be achieved by designing a radial pistons cam- lobe motor specifically for such power-intense applications. This study describes a radial pistons cam-lobe motor design engineered to maximise tool productivity, and availability throughout the machine’s lifespan. The example of a harvester head for processing trees is taken as a benchmark application to demonstrate performance improvements. After describing this particularly harsh application, a representative reference usage cycle, and productivity metrics are proposed. A radial pistons cam- lobe motor design optimised to allow productivity improvements on the tree harvester head is then introduced, and a simulation model of the harvester head installed on its base machine detailed. In a comparative simulation study, the upgraded motor is substituted for the reference component on the harvesting-head and both models are simulated over the previously introduced reference usage profile. In conclusion, the respective performances and the demonstrated productivity gains are discussed. SUSTAINABLE FLUID POWER Wed Sep 9, 4:10 PM, Stewart Center 279

P13: How Fluid Power Research Can Contribute to a More Sustainable Construction Industry

By: Olivier Reinertz, Christian Bertram and Katharina Schmitz (Institute for Fluid Power Drives and Systems (ifas), RWTH Aachen University, Germany)

When: Wednesday 9 September 2026 (Day 2), 16:10-17:30 ET

Where: Stewart Center, Room 279

Session: Sustainable Fluid Power, chair Aleksandar Egelja

Order: talk 1 of 4, about 20 min each

Type: Technical presentation with published abstract

Full author list: Olivier Reinertz, Christian Bertram, Katharina Schmitz (Institute for Fluid Power Drives and Systems (ifas), RWTH Aachen University, Germany)

Abstract: The construction industry is facing severe challenges in near future. The reasons are widespread. First, the growing earth population leads to a continuously rising demand for infrastructure, living and industrial space, forcing the construction industry to raise productivity. On the other hand, the building and construction sector is responsible for approx. 34 % of the global anthropogenic CO2 emissions, while this share will grow further with enhanced construction activity. Significant parts of these emissions result from the production of building materials. Cement production alone generates approx. 6 % of the global emissions, due to its enormous used quantities and high temperature requirements in production. Paradigm changes in raw material selection, building designs, and material use are therefore unavoidable. Additionally, the drive systems of mobile construction machines contribute to the sector’s emissions. While construction principles need to change, the requirement for earth moving and mining and thus for more efficient and emission-free working machines persists. Finally, construction is a labor-intensive branch, facing severe problems with recruitment due to the shrinking number of young people in many industrialized countries and the direct concurrence with more attractive, less physically demanding jobs. The paper shows how fluid power can contribute to an ecologically and socially more sustainable construction industry by means of several examples from current research at ifas and beyond. Herein, both dimensions of sustainability are simultaneously optimized by automation of construction processes, e.g. by means of partly automated mobile machines with additional intelligence, to allow real time surveillance of the building progress, fluid power enabled automated prefabrication of lightweight assemblies, which require less concrete and labor on site, and enhanced switching schemes and fluid selection for mobile hydraulics to ensure increased energetic efficiencies.

Published paper (PDF): https://www.riverpublishers.com/downloadchapter.php?file=RP_9788743816782C2.pdf

P14: Electrification-Enabled Hydraulic Architecture: Improving Efficiency and Total Cost of Ownership

By: Justin Hernan (Parker Hannifin, USA)

When: Wednesday 9 September 2026 (Day 2), 16:10-17:30 ET

Where: Stewart Center, Room 279

Session: Sustainable Fluid Power, chair Aleksandar Egelja

Order: talk 2 of 4, about 20 min each

Type: Technical presentation with published abstract

Full author list: Justin Hernan (Parker Hannifin, Hydraulic Pump and Motor Division)

Abstract: Hydraulics have long been foundational to productive machines, and electrification is now enabling new electro-hydraulic architectures that improve duty-cycle efficiency and controllability without giving up the unrivaled power density and robustness hydraulics provide. Electrification is enabling hydraulics to be packaged and controlled differently – favoring duty-cycle-optimized, on demand operation, integrated diagnostics, and hybrid partitioning of machine functions – so electrified platforms can capture efficiency gains, reduce total cost of ownership all without sacrificing system performance. This presentation focuses on architectural changes enabled by electrification. Topics include variable speed electro- hydraulic power systems, on-demand pressure and flow, and centralized versus decentralized concepts. A duty- cycle-based comparison framework is used to quantify efficiency and performance tradeoffs including standby losses, operating point shifting with variable speed capability, and thermal and noise behaviors. Duty-cycle and laboratory-based testing are used to evaluate system architectures over representative operating cycles to guide parameter and component selection. Anticipated results include: (1) quantified duty-cycle impacts showing where electrification-enabled hydraulic architectures reduce energy consumption without compromising system performance. (2) A practical selection framework clarifying where traditional hydraulics remains the best solution, and where hybrid electro-hydraulic architectures can ease battery and drivetrain demands and help reduce overall emissions.

P15: Full 3D CFD and FEM Validation of Surrogate-Optimized Hydraulic Manifolds Designed via the MOThEA Framework

By: Samuele Nizzardo, Andrea Vacca and Alberto Benato (University of Padova, Italy and Purdue University, USA)

When: Wednesday 9 September 2026 (Day 2), 16:10-17:30 ET

Where: Stewart Center, Room 279

Session: Sustainable Fluid Power, chair Aleksandar Egelja

Order: talk 3 of 4, about 20 min each

Type: Technical presentation with published abstract

Full author list: Samuele Nizzardo, Alberto Benato (University of Padova, Italy); Andrea Vacca (Maha Fluid Power Research Center, Purdue University, USA)

Abstract: Despite their high power density and robust performance in aerospace and mobile applications, traditional hydraulic actuation systems are increasingly scrutinized for their energy consumption and operational efficiency. In this context, optimization of the hydraulic manifold architecture plays a key role. The internal routing of these components strongly affects both steady-state flow losses and overall structural mass, making manifold layout a critical factor in improving fluid-dynamic performance and the efficiency of next-generation hydraulic systems. This paper presents the CFD and structural validation of a fully automated design algorithm for the generation of optimized internal flow topologies in additively manufactured hydraulic manifolds (MOThEA, Manifold design Optimization through Theta* path finder and Evolutionary Algorithms). The proposed framework implements a self-executing sizing methodology that estimates pressure drops using an adapted Ito correlation and determines the minimum safe wall thickness through Lamé equations. Compared with conventional design workflows, which typically require time-consuming manual iterations, the proposed approach significantly reduces design time (less than 25 minutes for a complex real-world application) while enabling a systematic exploration of highly efficient manifold configurations. To validate the algorithm, a reference optimized manifold geometry was analyzed. Assuming the same material, the CFD results show that the optimized topology reduces pressure losses by more than 84% compared to a conventional cross-drilled baseline. Full 3D CFD and FEM Validation of Surrogate-Optimized Hydraulic Manifolds Designed via the MOThEA Framework At the same time, finite element structural analysis shows that despite a 93.1% reduction in weight, the optimized manifold satisfies structural integrity requirements under operating pressure. Although the present mass evaluation does not include valve-thread connections or support structures, the results demonstrate the reliability of the proposed algorithm in generating feasible ultra-lightweight manifolds with markedly reduced parasitic losses.

Published paper (PDF): https://www.riverpublishers.com/downloadchapter.php?file=RP_9788743816782C14.pdf

P16: Energy Saving Strategies in Hydraulic-Driven Machine Design

By: Medhat Khalil (Milwaukee School of Engineering, USA)

When: Wednesday 9 September 2026 (Day 2), 16:10-17:30 ET

Where: Stewart Center, Room 279

Session: Sustainable Fluid Power, chair Aleksandar Egelja

Order: talk 4 of 4, about 20 min each

Type: Technical presentation with published abstract

Full author list: Dr. Medhat Khalil, PHD, CFPHS, CFPAI, Program Director of Fluid Power Education (Milwaukee School of Engineering, Milwaukee, WI, USA)

Abstract: Hydraulic control systems serve almost all industries around the globe, on the ground, in the water, and in the air. Hydraulic-driven machines are extensively and widely used worldwide, whether for stationery or mobile applications, and whether for civil or military applications. Hence, every fraction of energy saving and efficiency improvement has a significant impact on the amount of carbon emission that can be cut. This presentation discusses a roadmap of energy saving as applied to hydraulic-driven machines. The road map shows in brief various architectural, constructional, and operational strategies for energy saving in hydraulic driven machines on both the component and the system level. However, for space limitations the presentation discusses only few selected topics from the presented road map. DRIVE AND STEER-BY-WIRE Thu Sep 10, 8:30 AM, Stewart Center 278

Checkpoint 5 of 5: PAP-DAY2-PM-CHK-5-93E19

You have reached the end of this page. If you cannot find checkpoint 5 above, you received only part of the page and should say so.